Important Plumbing Tips for Installing a Bathtub
Important Plumbing Tips for Installing a Bathtub
Blog Article
We have encountered this article involving A Step-by-Step Guide to Installing a Bathtub listed below on the internet and felt it made perfect sense to write about it with you on this site.
Mounting a bath tub isn't precisely brain surgery, but it does call for strong plumbing, carpentry, and in some cases, tiling skills. Changing an old bathtub with a brand-new one is likewise a moderately tough task. If the old tub is easily accessible, the project can move immediately; if you have to open a wall to get rid of the old bathtub and place the new bath tub, the task is a lot harder. In either case, the task is within a home handyman's skills, although you will certainly require an assistant to move out the old bathtub and embeded in the new one. Make sure you have actually qualified yourself for the work and are comfortable trying it. As opposed to hiring a contractor to take control of a halfway-completed job, it is better to think about using one before you begin. Possibilities are you may require an expert plumber to make tube connections.
This write-up will certainly assist you set up a new bathtub in your restroom if you have actually currently gotten a brand-new bathtub and also do not need to alter the plan of your previous water supply pipes.
Your devices and also product list must comprise the following:
Getting ready for the Installment
Firstly, the supporting structure provided with the bath ought to be fitted (if called for) according to the maker's instructions. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is necessary to make certain that if the tap includes a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the taps system to avoid strain on the tub.
Fit the adaptable tap ports to the bottom of both taps utilizing 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bath. Use the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Ensure you make use of all of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom must now be ready to be fitted in its final position.
Removing Old Taps
If you require to replace old taps with new ones as a part of your installation, after that the first thing you should do is disconnect the water system. After doing so, switch on the faucets to drain pipes any water staying in the system. The process of removing the existing faucets can be rather problematic as a result of the restricted accessibility that is commonly the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a towel all set for the continuing to be water that will come from the pipelines. As soon as the supply pipelines have been eliminated, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from transforming throughout this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old securing substance.
Prior to carrying on to fit the brand-new taps, compare the pipeline connections on the old taps to the new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Installing the Bathtub
Using the two wood boards under its feet, place the bathtub in the required position. The wooden boards are useful in evenly spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto four tiny points.
The next goal is to ensure that the bath tub is leveled all round. This can be achieved by inspecting the spirit level and also adjusting the feet on the bathtub until the spirit level reviews degree.
To set up faucets, fit all-time low of the furthest adaptable tap adapter to the appropriate supply pipeline by making a compression join; after that do the exact same for the other faucet.
Switch on the water and inspect all joints and also new pipework for leakages and also tighten them if required. Load the bathtub and likewise examine the overflow electrical outlet and the typical outlet for leaks.
Ultimately, deal with the bath paneling as explained in the maker's user's manual. Tiling as well as securing around the tub ought to wait until the bathtub has been used at least once as this will resolve it right into its last position.
Fitting New Touches
If the tails of the new taps are plastic, then you will certainly need a plastic adapter to stop damage to the string. One end of the connector fits on the plastic tail of the tap and also the other end provides a link to the existing supply pipes.
If you require to fit a monobloc, after that you will certainly require lowering couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, place the tap in the mounting opening in the bath/basin making sure that the washing machines remain in location in between the tap and also the sink. Protect the tap in place with the manufacturer offered backnut. When the tap is safely in position, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with normal tap connectors. The former kind should be attached to the tap finishes first, tightening up just by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the area where the bath satisfies the floor tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the installation can move enough to split a rigid seal, triggering the water to penetrate the wall in between the bathroom and also the tiling, leading to complications with wetness and also possible leaks to the ceiling below.
You can select from a range of coloured sealers to assimilate your fixtures and also installations. They are offered in tubes and also cartridges, as well as are capable of sealing gaps as much as a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always fill the tub with water prior to sealing, to allow for the activity experienced when the tub remains in use. The sealer can fracture rather early if you do not take into account this movement prior to sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also easily readily available on the market. It is a good idea to fit the tiles using water-resistant or waterproof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you liked our excerpt on Installing A Bathtub. Thanks a ton for taking the time to read through our posting. Are you aware of someone else who is excited about the niche? Be sure promote it. Thanks a lot for your time. Come back soon.
Fix it ASAP! Call. Report this page